POWER UNIT
| Engine: |
DEUTZ |
| Type: |
TCD 2013 L06 2V |
| Kind: |
6-cylinder diesel engine, liquid-cooled |
| Output: |
|
| Nominal: |
182 kW / 2,000 rpm |
| ECO Mode: |
169 kW / 1,700 rpm |
| Fuel Tank: |
450 litres |
| Electrical System: |
24 V |
UNDERCARRIAGE
| Crawler Tracks: |
provided with rubber pads |
| Ground Contact: |
3,060mm x 305mm |
| Suspension: |
rigid |
| Track Tension Adjuster: |
spring assembly |
| Track Rollers: |
lifetime grease lubricated |
| Traction Drive: |
hydraulic, separate drive and electronic control provided for each crawler track |
| Speeds: |
|
| Pave Speed: |
25 m/min |
| Travel Speed: |
4.5 km/h |
| Service Brake: |
hydrostatic |
| Parking Brake: |
spring-loaded multiple-disk brake, maintenance-free |
MATERIAL HOPPER
| Hopper Capacity: |
14 tonnes |
| Width: |
3265mm |
| Feed Height: |
615mm (bottom of material hopper) |
| Push-Rollers: |
oscillating, displaceable forwards by 100mm |
CONVEYORS AND AUGERS
| Conveyors: |
2, with replaceable feeder bars, conveyor movement reversible for a short time |
| Drive: |
hydraulic, separate drive provided for each conveyor |
| Speed: |
33 m/min. |
| Augers: |
2, with replaceable auger blades, auger rotation reversible |
| Diameter: |
480mm |
| Drive: |
hydraulic, separate drive provided for each auger |
| Speed: |
60 revs/min. |
| Auger Height: |
|
| Standard: |
infinitely variable by 15cm, mechanical |
| Option: |
infinitely variable by 15cm, hydraulic |
| Lubrication: |
Centralized Lubrication System with electrically driven grease pump for conveyor and auger bearings |
SCREED
| AB 600-2 IP (): |
|
| Basic Width: |
3m, infinitely variable range 3m to 6m |
| Maximum Width TP2: |
8.5m |
| Layer Thickness: |
30cm |
| Screed Heating: |
screed plates, tamper bar and pressure bar(s) heated electrically |
| Power Supply: |
three-phase A.C. generator |
MIX CONVEYING SYSTEMS
| Worm Conveyors in Receiving Hopper: |
2, with hydraulic drive |
| Diameter: |
400mm |
| Belt Conveyor: |
1, with hydraulic drive |
| Width: |
1100mm |
| Conveying Capacity: |
1200 tonnes/h* |
TRANSFER MODULE
| Holding Capacity: |
20 - 24 tonnes (to be placed into the material hopper |
| |
of the paver) |
RECEIVING HOPPER
| Width: |
3,680mm (hopper sides folded out) |
| Feed Height: |
600mm (bottom of receiving hopper) |
TRANSFER MODULE
| Belt Conveyor: |
1, with hydraulic drive |
| |
radiant heaters (propane) |
| |
hydraulic belt tension adjuster |
| Width: |
1,000mm |
| Conveying Capacity: |
900 tonnes/h* |
DIMENSIONS AND WEIGHTS
| Length: |
Tractor Unit and Screed in Transport Position |
| Weights: |
Tractor Unit with Screed |
| Key: |
|
| TP2: |
equipped with Tamper and 2 Pressure Bars |
| IP: |
InLine Pave® |
| *: |
dependent on type of mix |
Technical alterations reserved.
